Dlink DAP-1360: Repeater Mode Configuration

In Repeater mode, the DAP-1360 increases the range of your wireless network by extending the wireless coverage of another AP or wireless router. The APs and wireless router (if used) must be within range of each other. Make sure that all clients, APs, and the wireless router all use the same SSID (wireless network name), channel, and security settings.

Assuming that you will manually configure your dap-1360 as a repeater.

1. Enter the Device Name of the AP and click next. (default is dlinkap).
2. Select Repeater from the drop down menu.
3. If you want to change the admin password, enter a new password and click next.
4. Select Manual configuration to setup your network manually.
5. Enter the Network name (SSID) of the network or you could use Site Survey to search for your wireless network you want to connect to.
6. Find your access point from the list, and click connect.
7. Choose which Security Mode you want to use.
8. Enter your preferred wireless security password. click Next to complete the setup.
9. Click finish.

You can also try to read, DLink DAP-1360: Access Point Configuration. 

DLink DAP-1360: Access Point Configuration

Overview: The Wireless N Access Point (DAP-1360) enables you to create a new wireless network or simply extend your existing wireless network coverage.Though, it uses several different modes, we will be tackling more on Access Point configuration in this topic.

Configuration:

1. Connect Patch cord to the LAN Port of DAP-1360, and put the other end on your Laptop or Desktop.Or you can connect to it thru WiFi. You may have to temporarily set your IP Address to static. (e.g. 192.168.0.51)
2. Run a web browser, and type in the default IP address 192.168.0.50.
3. In the User Name field, type in the default name admin, Leave the password field blank.
4. Once you have logged in, click Wireless Setup in the left pane.
5. Select Access Point as the wireless mode.
6. Change the default Network Name (SSID) to your preferred name.
7. Disable the Auto Channel Selection if you want to change the default ( Channel 6) channel.
8. Go to Security , select you preferred security encryption and type in your password.
9. Click Save Settings. 

How to access Advance Settings and DMZ in ZXDSL 831ii modem?

1. Type 192.168.1.1 in the address bar
2. When prompt with username and password. Use 'admin' and 'bayandsl', respectively without the qoute. 
3. Go to Advance, in the left pane click NAT.
4. Click DMZ, choose Enable.
5. Enter the IP Address of the device you want to access in the internet.
6. Click Save.

To make sure your entries has been saved, Reboot the modem and access it again.

How to reset Epson C59/ME2/C79/CX3900?

Error: Parts Inside Your Printer Has Reached The End Of Its Service Life

1. Download First the resetter for Epson C59 here.
2. Unzip. Open the extracted folder.
3. Run INDORESET.BAT and follow the instruction.
4. Run adjprog.exe
5. Click Accept
6. Click Particular Adjustment Mode.
7. Go to Maintenance then Select Waste ink pad counter then click ok.
8. Click on "check button" till its done then click on "initialization button" then click on "finish button".
9. Switch off printer for 5secs then switch on again.
10. After you reset succesfully, go back in INDORESET.BAT windows and you can change the date back to normal.

Linksys WRT120N: How to block website?

Scenario:
In this scenario, management wants to block all social networking sites, porn sites and others. Only the 2 laptops used by the management should be able to access all the sites. first, what we did is we set all 30 client computers to static ip addresses (e.g. 192.168.1.1 to 192.168.1.30). Now for the router,

1. Go to Security - Firewall and then make sure SPI Firewall is enabled.
2. Enable NAT Filter Redirection.
3. Go to Access Restrictions - Internet Access 
• Select Policy Number from the drop-down menu.
• Enter a Policy Name in the field provided, and select Enabled.
• click Edit List ( this time, we enter the ip range of the PCs.192.168.1.1 - 30)
• and then click Save Settings.
• For Access Restrictions, choose allow.
• Decide which days and what times you want this policy to be enforced.
• Enter each URL in a separate Website Blocking by URL Address field, for specific URL addresses
• Enter each keyword in a separate Website Blocking by keyword field, for blocking website using specific keyword.
• click Save Settings to save the policy's settings. 

How to setup access point routers using your Wi-Tribe modem?

Want to share your internet access to others using your Wi-Tribe 4G and yet enjoying wi-fi connectivity? Here is a tutorial on how to setup routers for your wi-tribe.We will use your router as an access point for the wi-tribe modem.In this setup, The wi-tribe will be the one to provide ip addresses and the router will be used as a wireless connection point.Thus, if you have to port forward any ip address, you have to put it on the Port Forward setting of your modem.

1. First, configure your router.Setup all the settings needed.Like, Wireless Settings(SSID, Wireless Channel) and Wireless Security(Pass-key).
2. Disable Use Router as DHCP Server in LAN Setup if you are using Neatgear JWNR2000. Now, in this portion, disabling dhcp server depends on your router.Like, for DLink DIR-600, you just have to enable Access Point Mode and thats it.
3. For other routers, Read your routers' manual on how to disable dhcp server or to have them as access points.
4. Connect the patch cable of your modem to any of the Four(4) Ports of the router.and if you are wired, just connect your cable to other three ports that was left and wait until you are connected.

EagleEyes:Remote View of CCTV Surveillance Camera using Mobile phones and Laptops

We discussed on our past post about dvr network configuration, that you were be able to view your cctv surveillance camera on your mobile phones, though we did not include the software you have to use. Here, we will show you how to install and configure EagleEyes. Takenote that this are applicable for some dvr's. But first, you should create an account.

Now, if you already have an account, go to AVtech EagleEyes site again.

1. Click on Software.(Leftside of your screen)
2. Under that, choose your mobile OS.(e.g. if your using iphone choose iphone and/or choose android if you are using Android OS, Ipad for Ipads, Blackberry for Blackberry phones, Symbian for Nokia Phones, Win Mobile for Phones that uses Windows Mobile, Video Viewer for Windows laptop or MacBooks and more.)
3. On the center, click Download. if you're not logged in, they will look for your id and password. so just enter them.
4. After downloading, install the program and just follow what are configuration instructions for each softwares.
   
   Here is the complete instruction in installation and configuration of  EagleEyes.click here.

HUAWEI ECHOLIFE BM622 WIMAX CPE: Unlock Admin Settings

If you are using Globe Wimax, probably your modem/router model is huawei echolife bm622 wimax cpe and your local ip is 192.168.1.1.

Now, if you access the router, you'll find out that the settings are limited, like there is no advance setting and others. Here are the procedure to unlock admin settings of globe wimax:

1. Open up web browser and type on the address bar: 192.168.1.1, and for the username: user and password: user
2. After you logged in, open another tab and copy and paste this on the address bar: http://192.168.1.1/html/management/account.asp
3. Account Settings will appear, Right-click and select view source code. 
4. In column 22, you'll find the username and password.
5. Copy the username and password, and use that to unlock the admin settings on your globe wimax.

CCTV Remote Viewing: Network testing and troubleshooting

Your done with dvr setup and configured router port forwarding and dmz(Demilitarized Zone). We now have to test your network. try to ping your dvr (e.g. ping 192.168.2.10), if you are able to ping it, then thats great, you have done it well locally. now for the host (e.g. mydvr.dyndns.org), tell a friend to try to ping your web ip address or your hostname. if he's able to ping them, your network is propery configured. But if not, try to see if you already configured the dmz or port forwarding of your router.

Here are few other reasons your service may not resolve correctly:

    * Typo: The simplest and most common problem is a typo. Double- and triple-check your spelling to make sure you are not transposing a letter or putting the wrong TLD (e.g. .net instead of .org).
    * Service is still in cart: Dynamic DNS hosts are placed in your shopping cart when you click the Create Host button. You must complete checkout to activate the hosts.
    * Service has not been created: When a new account is created, it does not contain any hosts. You need to add a hostname to begin using the service.

click HERE for the complete link of troubleshooting your network.

HDD REGENERATOR: Save and secure your hard disk files

We dont want to see our computers not booting in windows, do we? and we dont want to lose our files either.It is really frustrating that your trying to access your files but the thing is you cannot open them. The saddest part is that you cant open your drives too. how is that happen?

Well, there are lot of factors that can cause a hard drive to fail and they are almost all preventable if you know how to take good care of your hard drive and your computer as well. Anyway, probably the biggest cause of hard drive failure could be the Bad Sector. A bad sector is a sector on a computer's disk drive or flash memory that cannot be used due to permanent damage (or an OS inability to successfully access it), such as physical damage to the disk surface or failed flash memory transistors. It is usually detected by a disk utility software such as CHKDSK or SCANDISK on Microsoft systems, or badblocks on Unix-like systems. When found, these programs may mark the sectors unusable (all file systems contain provision for bad-sector marks) and the operating system skips them in the future.(wikipedia)

Good thing there is HBCD, we've been using this tool and so far, it does not disappoint us. HDD Regenerator is a unique program in hbcd for regeneration of physically damaged hard disk drives. It does not hide bad sectors, it really restores them. It can repair damaged hard disks without affecting or changing existing data. As a result, previously unreadable files and drives are recovered. 

CCTV Remote Viewing: Creating Account and Hostname in DynDNS

DynDNS Free allows you to create a hostname that points to your home or office IP address, providing an easy-to-remember URL for quick access. They also provide an update mechanism which makes the hostname work with your dynamic IP address.

1. Open www.dyndns.com and create an account and confirm it.
2. Create a free Dynamic DNS host.
3. On My Services, click on My Host and then Add new host.
4. On the textbox put your chosen address or hostname and select from the web extension that you want. Then click,  your current location's ip address is ***.***.***.***.
5. Add to Cart, proceed to checkout then Activate Services.

How to Reset Epson T13, T1100 and TX121

Error: Parts Inside Your Printer Has Reached The End Of Its Service Life

First download the resetter here.

1. Open Adjustment Program. click accept.
2. Select Particular Adjustment Mode. 
3. Select your Destination, Printer Model and Port. click ok.
4. Go to Waste Ink Pad Counter. click ok.
5. Click check to view the waste ink pad counter.
6. Check the Main Pad Counter and click Initialization to fully reset the printer

Web Hop: Create free Re-direct domain with DynDNS

1. Make a free account at www.dyndns.com.
2. Log into DynDNS
3. Go to My Account
4. Go to add host services
5. Type in the custom domain you like and pick the web extension you want.
6. Click on webhop redirect
7. Type in your existing subdomainb e.g. yourname.yourhostname.com
8. click save changes
9. Test your domain. To do this, type in the new domain you chose. it should redirect you to the lengthy URL you used before.

CCTV Remote Viewing: DVR NETWORK CONFIGURATION

Having a CCTV surveillance camera today is a must for every offices, home and other businesses infrastructure..but being able to view them through any various PDA phones like Android phones, BlackBerry phones, iPhone, iPod, iPad, Windows Mobile phones and laptops is what we need in this very fast pace world.

Now if you already had a CCTV installed in your area, then thats great! But the first thing you really need to consider is that your DVR( Digital Video Recorder) should or must be Internet capable or at least should have a LAN Port.Through that port youll be able to connect to the router or modem which will make your DVR accessible to your gadgets.

Second, you have to configure your dvrs' network setup.

DVR Network Configuration:

Using a modem:

Adjust the DHCP mode Setup to whatever your ISP provider provided you. for example,

• if you are using DHCP or automatically obtained ip address. select DHCP.
• if you are using STATIC IP, just assign your intenal ip address for the dvr and assign the gateway and primary address from your modem.( you can skip creating account at dyndns.com)

 
Use menu on DVR to assign internal IP and gateway and port number.You have to take note of the port number you have entered coz it will be used on Port Forwarding.

Using a router:

Look for Gateway. If the Gateway is 192.168.1.1, then you can make the DVR's IP anything from 192.168.1.2 - 192.168.1.255

Input the ip address to DMZ(demilitarized zone) or port forwarding.

So we have now an installed cameras, an Internet Capable DVR, and a router or modem. Now where in for Creating an account at www.dyndns.com.

Next: Creating dyndns account and Hostname.