Linksys WRT54G2: DMZ and DDNS Settings

DMZ Settings:

1. Click Applications and Gaming then DMZ.
2. Select Enable and enter the IP address of the device you want to access in WAN.
3. Click Save Settings.

DDNS Settings:

1.  On Setup, select DDNS.
2. Enable DDNS Service.
3. Select your Dynamic DNS provider.(e.g. Dyndns.org)
   
4. Enter username, password and hostname, respectively. (make sure you have already created hostname for your device, for it to update successfully.)
   
5. Click Save.

PLDT myDSL ZXV10 W300: DMZ and DDNS Settings

For Demilitarized Zone (DMZ):

1. Type 192.168.1.1 in the URL address
2. Enter adminpldt and 1234567890, as username and password respectively.
3. Go to Advance Setup, click NAT.
4. Click DMZ,  select Enable then enter your device IP address in DMZ Host IP Address.
5. Click Save.

For DDNS Setting:

1. Go to Access Management.
2. Click DDNS
3. Select Activated to Enable Dynamic DNS.
4. Enter hostname, username and password  of your dyndns account for your dvr.
5. Click Save.

Motorola WiMax CPEi25725: DMZ and Port Forwarding

If you are using Motorola WiMax CPEi25725 modem, your default gateway is probably 192.168.15.1. Now, here are the steps on how to Port Forward on you modem.

1. Open a browser, type 192.168.15.1 on the url address bar.
2. Type motorola for password.
3. On the upper right side, click Port Forwarding.
4. If you only have one device behind the router, use DMZ or else, click Forwarding for you to add devices.
5. For DMZ, Type in the IP address of the device you want to access from the internet. 
6. Click Apply.
7. For Forwarding, Click radio button for Select.
8. Choose TCP.
9. Enter Start - End WAN Port.
10. Enter IP Address.
11. Enter Start - End LAN Port.
12. Click Enabled.
13. Click Add, and then Apply to save your configurations.

How to access PLDT MyDSL HG530 DMZ settings?

If you are using PLDT MyDSL HG530 Modem, your default gateway should be 192.168.1.1.

1. Enter 192.168.1.1 on the address bar, when prompt with login. use username: adminpldt, password: 1234567890
2. On the left pane, click Basic, under that choose NAT.
3. click on DMZ, enter the IP address you would want to access in WAN.
4. click submit.

To make sure that your entry has been saved, try to restart the modem and access the dmz settings again.

Dlink DAP-1360: Repeater Mode Configuration

In Repeater mode, the DAP-1360 increases the range of your wireless network by extending the wireless coverage of another AP or wireless router. The APs and wireless router (if used) must be within range of each other. Make sure that all clients, APs, and the wireless router all use the same SSID (wireless network name), channel, and security settings.

Assuming that you will manually configure your dap-1360 as a repeater.

1. Enter the Device Name of the AP and click next. (default is dlinkap).
2. Select Repeater from the drop down menu.
3. If you want to change the admin password, enter a new password and click next.
4. Select Manual configuration to setup your network manually.
5. Enter the Network name (SSID) of the network or you could use Site Survey to search for your wireless network you want to connect to.
6. Find your access point from the list, and click connect.
7. Choose which Security Mode you want to use.
8. Enter your preferred wireless security password. click Next to complete the setup.
9. Click finish.

You can also try to read, DLink DAP-1360: Access Point Configuration.